PVC Ducting Tape (Silver) - HEVAC Tape
This duct Tape is designed to efficiently seal duct joints in heating and air conditioning systems. It prevents air leakage and stops dirt, dust and fumes from entering system. Adheres to metals, most plastics or glassfibre materials.
Size: 50mm x 33m
TECHNICAL DATA SHEET
Vinyl Duct Tape made from PVC sheeting coated with a pressure sensitive adhesive with high adhesion
Tape Thickness: 0.16mm
Tensile Strength at Break: 31.5 N/10mm
Elongation at Break: 200%
Adhesion to Steel: 2.4 N/10mm
Adhesion to Self: 2.4 N/10mm
Service Temperature: 0°C to 70°C
Application Temperature: 0°C to 40°C
Recommended Storage Temperature: 10°C to 20°C
Shelf Life: 12 months
Length of Roll: 33M
Width of Tape: 25, 38, 50, 75, 100, 150mm
Core Size: 76mm
Colours: Silver only
Joint sealing metal or plastic ducting below 70°C operating temperature. Jointing PVC faced glass fibre.
Ensure that all surfaces to be bonded are dry, free from dust, grease and other contaminants. Surfaces to be
bonded and tape to be applied should be at a temperature within the limits of the Application Temperature
recommended in the relevant Product Information Sheet. This is particularly important if the tape has been
stored in a cold area. Apply the tape by using the maximum amount of pressure possible, smoothing down to
achieve 100% contact.
Joins in rolls of tape may occasionally be found. Every endeavour is made to reduce these to a minimum but
users should not rely on the tape being one continuous length. When using tapes that have a siliconised paper
as an interleave, remove this paper from the floor area as quickly as possible to minimise the risk of slipping.
Self adhesive tape is not a hazard to health providing it is used correctly. PVC tapes are not recommended for
gas fire back plate sealing.
Except where indicated otherwise, the above figures are average values and should not be regarded as
maximum or minimum values for specification purposes. The company reserve the right to improve products
and change specifications, which may alter performance. We advise the customer to test the material required
to ensure the suitability of intended application.
MATERIAL SAFETY DATA SHEET
Polyvinyl chloride tapes. Odourless.
Not a fire hazard in open areas.
Water fog, foam, CO2, and dry chemicals can be used on fires.
COMPOSITION AND INFORMATION ON INGREDIENTS:
Chemical Name Weight% CAS No.
Rubber Adhesive 17-21
PVC Resin 54-60 [9002-86-2]
Plasticizers 21-25 [117-81-7]
Lead Stabilizer Compound 20,000PPM↓
Pigments (organic and/or
Cd Compound 10PPM↓
Toluene 0-1 [108-88-3]
4. FIRST AID MEASURES:
Eye Contact: Immediately flush with copious amounts of water for at least 15 minutes. Get medical
Skin Contact: No potential health effects are anticipated.
Inhalation: No adverse effects anticipated by this route of exposure incidental to proper industrial handling.
If Swallowed: Drink two glasses of water. Call a physician.
Note to Physician: Treat symptomatically. Treatment may vary with condition of victim and specifics of
FIRE FIGHTING MEASURES:
Flash Point (Method Used): 320-390°C (ASTM D-1929) Flammable Limits: N/A
Extinguishing Media: Water, dry chemical, foam, CO2.
Special Fire Fighting Procedures: Wear self-contained breathing apparatus and protective clothing to
prevent contact with skin and eyes.
Unusual Fire and Explosion Hazards: Any vinyl and adhesive can be forced to burn by continuous
application of intense heat.
ACCIDENTAL RELEASE MEASURES:
Sweep up and discard.
HANDLING AND STORAGE:
Handling: Caution with edge of sheet. After using this sheet, wash hands.
Storage: Keep dry and cool (below 25°C) and away from direct sunlight for quality.
8. EXPOSURE CONTROLS/PERSONAL PROTECTION:
Engineering Controls: Good general ventilation should be sufficient for most conditions. When processing
at elevated temperature, provide local exhaust.
Personal Protective Equipment (PPE): Respiratory Protection: For most conditions, no respiratory
protection should be needed. When processing at elevated temperature, use an approved respiratory
Specific Gravity (H2O=1): 1.3-1.4
Softening Point >80°C
Decomposition Temperature: 260°(C)/500°F
STABILITY AND REACTIVITY:
Incompatibility (Materials to Avoid): Not known.
Hazardous Decomposition of By-Products: CO2, CO, HC1 and some toxic gases.
Hazardous Polymerization: Hazardous polymerization will not occur.
Not a hazardous material for DOT shipping.
Chemical Inventories: The products are defined as an article by REACH regulations, and therefore are exempt
from the inventory listing requirements.
The information in this material safety data sheet presented herein was prepared for your reference to the best
of our knowledge. It is given in good faith but Campbell International make no warranties, expressed of implied.